The Next Generation of Power Generation
Our Home Page presents you with our
Progress and Milestones
Milestone
Reached: (September 24, 2010) AC Prototype 3 was re-assembled
incorporating a series of refinements and it became immediately apparent that
the rotating torque was very low. (Lower Torque = Less Horsepower will be
needed to spin the Mag Force Generator Technology) thus (Less Horsepower =
**Better Overall Efficiency).
In house testing confirmed that by setting up AC Prototype 3
with a ¼ horsepower electric motor and testing its ability to spin the
Mag Force Generator Technology. The ¼ horsepower motor was able to
rotate the prototype, revealing the lowest rotating torque requirement to date.
A series of in house functionality tests will now validate
all 8 output circuits on AC Prototype 3 and use the new shielding features to
improve the output voltage and circuit isolation. This is the preliminary
internal testing that will precede independent testing and many adjustments
will be made to keep the generator in a reliable operating condition through
varying temperatures.
**In comparison, a
¼ horsepower motor simply could not spin any conventional generator with
similar output wattage under full electrical load. This is a major breakthrough
in our development. Preliminary efficiency measurements are
being taken and documented.
AC Prototype3
currently going through final in house improvements before being sent out for
Third Party Independent Testing.
Milestone
Reached: (May 24, 2010) Mag
Force Generators tested a new configuration with AC-Prototype 3 and proved its successful function to greatly reduce
the required rotation torque. This permits a far smaller horsepower motor to
spin the Generator, which should significantly boost the overall efficiency.
Mag Force Generators announces
that inventor Richard Rogala has furthered the refinement process of its
cutting edge technology and advanced electrical generator design with Mag Force AC Prototype 3.
This refinement progression is possible
because Mag Force Generators proved with AC Prototype 1 that its revolutionary
design and technology did not slow down under full electrical load. Mag Force
Generators then built AC Prototype 2 and began the exciting fundamental step by
step processes needed to move Mag Force Generators forward and take this
ground-breaking technology to the threshold of commercial production.
Mag Force Generators has taken
what was learned from AC Prototypes 1 & 2 and incorporated many
improvements while building AC Prototype 3. Potentially each of these
improvements could provide very positive results. These are summarized as
follows:
1. Standard magnets are being replaced with seven times stronger Neodymium Iron magnets.
2. Laminated Silicone Iron is being replaced with Neodymium Iron for the
Coil Bars.
3. Improvements are being made to allow multi-module attraction and
repelling forces to be counteracted along a common shaft.
4. More efficient 120 Volt AC Coil output obtained from increased wire
diameter.
5.
To double the amount of power produced by the
overall Generator, by increasing the number of circuits from four (4), to
eight (8) independent circuits, each capable of potentially providing 120 Volts
AC.
Close expert analysis of AC
Prototype 2 has revealed both an opportunity to improve on the nullifying of
rotation-resisting forces and also produce more power from doubling the
available circuits with the added anticipated benefit of a reduction in the
torque requirement to spin the Generator. On May 24, 2010 Mag Force Generators
tested a new configuration and proved it successfully functioned to greatly
reduce the required rotation torque. This does permit a far smaller horsepower
motor to spin the Generator, which should significantly boost the overall
efficiency.
Within weeks AC Prototype 3 will
set in motion testing to determine how high the voltage is on the old Coils
with the new stronger Magnets and improved conductors. Then, within days take
this important data and rewind the Coils to bring the voltage back to 120 Volts
AC and re-assemble the device. Our target is, to have AC Prototype 3 fully
assembled and testing all of our improvements. This testing should continue to
confirm that the Mag Force Generator does not slow down under load, provide
some greatly anticipated total Mag Force generator wattage output measurements
and give the first indication of Mag Force generator efficiencies.
If in house test results are
favorable we will immediately enlist Lake
Superior State University’s Department of Engineering -- Prototype
Development Center for independent third party
verification. Mag Force Generators will then, embark on the move toward the
manufacturability and production phases needed to bring this product and
technology to the world.
Milestone
Reached: (March 19, 2010) Began Drafting plans and acquiring parts for AC-Prototype
3 Testing to begin mid May
1st Quarter
2010 Video Update
Milestone
Reached: (December 17, 2009) * IMPORTANT
NEWS * Claim verified in house on Prototype 2
Our claim and mission to success is that our product
does not slow down under load and our first prototype, Prototype 1 actually
sped up when it was put under load (see test results from Lake
Superior State University).
Recent testing on Mag Force
Generator Prototype 2 revealed that, with all 4 circuits under load, it
performs just as Prototype 1 did and, as we expected, Prototype 2 sped up under
load. The measurements were as follows:
Speed with no load - 1680 rpm
Speed
under load - 1730 rpm
(4 circuits in play)
This is very significant to
the future of Mag Force Generators, because remember, all other conventional
generators (our competition) slow down under load.
Milestone
Reached: (December 15, 2009) AC 120 Volts output from all 4 circuits
Mag Force Generators was able
to initially test all four circuits powering conventional incandescent light
bulbs simultaneously.
Milestone
Reached: (October 5, 2009) Prototype 2 Complete
Now assembled, efficiency testing is beginning to take place on the Mag Force Generator Prototype 2 and modifications are being made.
Video Update
Upper Peninsula Inventor Richard Rogala answers questions about his patented new electrical generator, a breakthrough in clean, affordable energy.
AC-Prototype 2 and DC-Prototype 1 are ready to roll out any day now.
(September 16, 2009)
Milestone Reached: (March 31, 2009) Drawings Complete
Final drawings for our second prototype are now complete and out for bids.
Once assembled, efficiency testing will take place of the Mag Force Generator Prototype 2 and modifications will be made.
Milestone
Reached: (March
25, 2009) Nullgrav in the News - Mag Force on TV-6 News
Milestone
Reached: (September 26,
2008) Mag Force Generator Test Complete - LSSU Test Report
Current electrical generators, when put under electrical load, have inherent inefficiencies.
Suppose you could increase power generation by up to 15 %, just by eliminating inefficiencies.
Suppose you could harness the physics of magnetism to allow a generator to continually spin with a net output of free electricity?
A new patented electrical
generator to dramatically increase the efficiency of power generation
About Mag Force Generator Milestones: Progress
in Prototype development is being managed by Richard Rogala (Inventor /
President). The documentation and business end of the corporation is managed by
Ed Janisse (Chairman of the Board / Chief Operating Officer).
© 2010 Nullgrav
Corporation d/b/a Mag Force Generators, All Rights Reserved
Box 373 * L’Anse
MI 49946-0373
906-395-2864
nullgrav@up.net